In this article down the page you can locate additional helpful answers in regards to How to Install a Bathtub Yourself.
Mounting a bathtub isn't exactly rocket science, however it does require solid plumbing, carpentry, and sometimes, tiling skills. Replacing an old tub with a new one is also a moderately tough job. If the old tub is easily available, the project can relocate easily; if you need to open a wall to get rid of the old tub and also place the brand-new tub, the task is much harder. In either instance, the task is within a residence handyman's abilities, although you will certainly need a helper to vacate the old tub and also embeded in the new one. Make sure you have actually qualified on your own for the task and fit attempting it. Rather than working with a service provider to take control of a halfway-completed project, it is far better to think about employing one prior to you begin. Opportunities are you may require a specialist plumber to make tube connections.
This post will assist you mount a new tub in your shower room if you have currently purchased a new tub and also do not require to transform the plan of your previous supply of water pipelines.
Your devices and material list should make up the following:
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installment, then the first thing you should do is disconnect the supply of water. After doing so, turn on the taps to drain pipes any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite problematic as a result of the limited gain access to that is usually the instance.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a towel prepared for the remaining water that will certainly come from the pipes. As soon as the supply pipes have actually been eliminated, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the single faucets from turning throughout this procedure. When the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned of any old securing substance.
Before moving on to fit the new taps, compare the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will need a plastic adapter to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the mounting hole in the bath/basin ensuring that the washing machines remain in location between the faucet and also the sink. Protect the faucet in position with the supplier supplied backnut. When the faucet is safely in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical faucet ports. The previous type needs to be linked to the faucet ends initially, tightening only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Installing the Bathtub
Using both wooden boards under its feet, position the tub in the required position. The wood boards are useful in evenly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 little points.
The next objective is to make certain that the tub is leveled all round. This can be achieved by examining the level and changing the feet on the bathtub till the spirit level reviews level.
To mount taps, fit the bottom of the outermost flexible faucet port to the appropriate supply pipeline by making a compression join; then do the very same for the other faucet.
Switch on the water system and inspect all joints and brand-new pipework for leakages and tighten them if needed. Fill up the bathtub as well as likewise check the overflow electrical outlet and also the typical outlet for leaks.
Finally, repair the bathroom paneling as defined in the producer's user's manual. Tiling as well as sealing around the bath tub ought to wait till the bathtub has actually been utilized at the very least once as this will certainly resolve it right into its final placement.
Preparing for the Installation
To start with, the sustaining structure provided with the bathroom needs to be fitted (if needed) according to the maker's directions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is important to see to it that if the faucet comes with a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets system to avoid pressure on the tub.
Fit the adaptable tap adapters to the bottom of both taps utilizing 2 nuts and also olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet with the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you utilize every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be suited its final setting.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to fracture a stiff seal, causing the water to pass through the wall in between the bathroom and the tiling, bring about problems with wetness as well as feasible leaks to the ceiling below.
You can pick from a selection of coloured sealers to blend in your components and also fittings. They are offered in tubes as well as cartridges, and also are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with twists of drenched paper or soft rope. Keep in mind to always load the tub with water prior to sealing, to allow for the activity experienced when the tub remains in usage. The sealant can fracture relatively early if you do not consider this movement prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise easily readily available on the market. It is suggested to fit the tiles utilizing waterproof or waterproof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were shown that editorial on Tools You Need to Install a New Bathtub from a good friend on a different website. For those who enjoyed our blog posting please remember to pass it around. Thank you for your time. Visit again soon.
Book-Now